Mini-project: Sokoban

               On these two weeks, we need to do the mini-project. The project title is Sokoban. That means we need to write a assembly game of Sokoban. In this game,  Player pushes boxes or crates around in a warehouse, trying to get them to storage locations.

              First of all, we need to connect the graphical LCD (128X64) and 6X4 keypad to our system board.

Schematic of keypad

pin assignment of graphic LCD

Here is the result of our final circuit

Final product

           

             

             And we write a test program to test whether the LCD display is work correctly or not. And finally we found out it is work. In this wrap wire experience, I feel some trouble on testing the circuit is work or not. However, I have learnt how to use CRO to find out the problem. I use CRO to trace the signal. Finally, I found out a active low pin remains low at all time. This technique is very useful.

           Now, we still are writing our assembly game. This is a challenging project. The workload is a bit high. We have to finish this project within 3 weeks. Therefore, we need to take the extra session to do this project. Although, this project is tough, I have learnt more things from this course. 

Experiment 6 -- Interface of the 8088 MPU with the 8259A PIC and LCD Module

In this week, I have done the experiment 6. This lab is to study the interfacing of the 8259A PIC with the 8088 MPU and the interfacing of the LCD module with the 8088 MPU. I need to Wrap wire the control signals of the 8259A and LCD module as shown in the lab manual, modify the I/O address field of the given test program to match our design of address decoder. Finally I need to write my own program to fulfill the following function, the switch button is pressed, my name and ID will display on the LCD.  When the button is pressed again, my partner’s name and ID will display on the LCD.

I need to according to the above figure to wrap wire, The typical one is pin7-14 of Character LCD are connected to AD0~AD7.  The pin 6 of character LCD is connected to GAL  pin17 which I have modified the address decoder  for selecting the character LCD.

For writing this assembly program, I need to initialize all the devices first. I write to loop function which can display the name of my partner and I sequentially.

     

loop1: check2: call check_key1         jnc check2         mov      dx,lcd_base         call TURN_LED1_ON         call display1         mov cx,50         call delay_X         check: call check_key1         jnc check         mov      dx,lcd_base         call TURN_LED2_ON             call display2          mov cx,50         call delay_X            jmp loop1

Also I have to write the display string function, which can display name on the LCD display.

outs1 db 'Cheng Ka Kui',0dh         outs2 db '1155003893',0dh         outs3 db 'Tai Pit Tat',0dh         outs4 db '1155023064',0dh                                     display1   PROC      NEAR         mov      dx,lcd_base busy7:     in         al,dx         and       al,10000000b         jnz        busy7         mov      al,00000001b    ;clear screen         out        dx,al ;display string1         mov      dx,lcd_base busy10:   in         al,dx         and       al,10000000b         jnz        busy10         mov      al,10000000b    ;set display address to 0         out        dx,al         mov      bx, offset outs1         call        print_string ;display string2                        mov      dx,lcd_base busy20:   in         al,dx         and       al,10000000b         jnz        busy20         mov      al,11000000b    ;set display address to 0         out        dx,al         mov      bx, offset outs2         call        print_string         ret display1   ENDP display2   PROC      NEAR         mov      dx,lcd_base busy72:   in         al,dx         and       al,10000000b         jnz        busy72         mov      al,00000001b    ;clear screen         out        dx,al ;display string3         mov      dx,lcd_base busy12:   in         al,dx         and       al,10000000b         jnz        busy12         mov      al,10000000b    ;set display address to 0         out        dx,al         mov      bx, offset outs3         call        print_string ;display string4                        mov      dx,lcd_base busy22:   in         al,dx         and       al,10000000b         jnz        busy22         mov      al,11000000b    ;set display address to 0         out        dx,al         mov      bx, offset outs4         call        print_string         ret display2   ENDP

Here is the result of our lab.

              

            

              After doing this lab, I have learnt how to write the assembly program. This is a very interesting lab. I can wrap wire to connect the device and write our own program. When the LCD can display the name and ID successfully, we felt a great sense of achievement.

Experiment 5 -- Parallel I/O and Timer/Count Interface

        On this two week, I had done the lab 5. The objective of Lab 5 is to study the interfacing of the 8255 PPI and 8254 PTC with the 8088 MPU. First of all, I need to wrap wire the control signals of the 8255 PPI and 8254 PTC as shown in the figure below.

         This is a very interesting hand work. After that, I have to write my own assembly program for the certain result. Once the switch button is pressed, the buzzer will be activated with a 1-KHz signal for a duration of around 0.5 seconds and all LEDs are turned on. If the button is pressed again, the all LEDs are turned off.

For verifying that I had generated 1-KHz signal, I used oscilloscope to see the output signal’s frequency as the below figure.

Here is the part of assembly program which set 1 KHz signal's frequency.

timer_1KHz_msb     equ     9   timer_1KHz_lsb     equ     196 ;When the switch is pressed, LEDs change state and sound 0.5 second. EXAMPLE1   PROC  NEAR       ;call  ram_test     ; Initialize the 8255 in mode 0     mov dx,i8255_base_address       mov al,10010000B ;set PA as input, set PB as output, set PC as output       inc dx       inc dx       inc dx                  ;point to command register       out dx,al        ;end initialize the 8255        ; Initialize the 8254 in mode 3     mov     al,00110110B       mov     dx,i8254_base_address       inc     dx       inc     dx       inc     dx       ;point to command register       out     dx,al       mov     dx,i8254_base_address       mov     al,timer_1KHz_lsb       out     dx,al       mov     al,timer_1KHz_msb       out     dx,al        ;end initialize the 8254

  To calculation of the value in MSB and LSB for generating 1 KHz

We know that the period of 1 KHz signal is 1ms. The period of a 2.5MHz clock signal is 0.4us. Therefore, the number of count for the counter is 0.5ms/0.4us= 9*256+196

Thus, MSB is 9 and LSB is 196.

This is a very interesting and meaningful lab. As this lab course is related to ELEG323 0(Microprocessors and computer systems). I have to use the knowledge that I have learnt in ELEG3230 to the lab. I feel proud of me that I can apply those things into the lab.